EPA-100-HA14-03-A023

100

2,800 千元

2011/01/03

2012/02/29

李嘉宜

回收基管會

顏素真

財團法人台灣產業服務基金會

化學物質管理

廢容器補貼變革、再生料驗證、連鎖販賣業評鑑

Waste container subvention reform, Regenerated plastics verification, and Fast-food chain store evaluation

黃宗煌

周函螢

02-27844188#239

kelly2788@ftis.org.tw

本計畫依據現行廢容器回收清除處理補貼作業方式所面臨問題，研擬規劃廢容器回收清除處理補貼費撥付方式調整方案，綜合分析廢容器回收清除補貼費不同撥付程序及撥付對象，包括：A1(補貼費率分為回收及處理補貼費率：回收清除補貼費採兩階段程序間接撥付予回收業，處理補貼費直接撥付予處理業)及A2(補貼費率未分為回收及處理補貼費率，補貼費總和全部撥付予處理業)；B1(已登記及未登記回收業均適用公告補貼費率)及B2(僅限已登記回收業適用公告補貼費率)。 此外，本計畫完成40家次連鎖速食店業輔導評鑑作業，評鑑對象共分為北、中、南三區，每區各由3位評鑑委員參與該區評鑑作業，並於100年12月6日辦理「連鎖速食店業資源回收成效輔導頒獎典禮」，予以公開表揚優良之業者。 本計畫針對15家廢塑膠容器受補貼處理廠進行現場訪查，與國內外產品使用消費後廢塑膠再生料之規範或驗證機制，研擬廢塑膠容器再生料之認證、驗證機制分別為(1)方案A：建立完整層級之廢塑膠容器再生料驗證機制；(2)方案B：建立銜接目前稽核認證制度之廢塑膠容器再生料驗證機制；(3)方案C：建立與目前稽核認證制度平行之廢塑膠容器再生料認驗證機制。方案B對現行制度的衝擊與成本影響最小，且符合目前廢塑膠容器處理業者之驗證需求，故建議推行此方案。

廢容器補貼變革、再生料驗證、連鎖販賣業評鑑

正式報告.pdf

6MB

2012/6/1 上午 12:00:00

According to the problems which waste container subvention have, we are going to develop a adjustment program of waste container subvention, and do the comprehensive analysis of different allocation of objects and procedures for waste container subvention, including A1 (divided subvention into rate of recycling and treatment, it takes two steps: the former is paid to the recyclers and the later is paid to the treatment.),A2 (one subvention only, the total amount will pay to treatment factories side.), B1 (no matter register or not, the subvention is applying to all recyclers.), and B2 (the subvention only apply to the registered recyclers.) Besides, finished counseling evaluation over 40 fast-food chain stores. The evaluative objects could be classified to northern, middle, southern Taiwan, three sections. Each section had 3 committee members to do the evaluation. And the “Evaluation the Effectiveness of Recycling of Fast-Food Chain Stores Ceremony” was held on Dec 6th, 2011 to praise publicly to entrepreneurs who had good performances. The project visited 15 waste plastic container treatment factories to study the domestic and foreign regulations and validation mechanisms about plastic recycling. The regenerated plastics certification mechanisms included: (1) option A(to build a comprehensive validation mechanism for recycled waste plastic material); (2) option B(to build a mechanism to connect the auditing and certification mechanism that we have); (3) option C(to build a mechanism which separate to the mechanism that we have). Option B has less impact and cost, also meets the requirement of treatment factories. Therefore, option B is the recommended proposal.

Waste container subvention reform, Regenerated plastics verification, and Fast-food chain store evaluation